Synergy Configuration Board "S1JA TB" R7FS1JA783A01CFM part_number: R7FS1JA783A01CFM rom_size_bytes: 262144 ram_size_bytes: 32768 data_flash_size_bytes: 8192 package_style: LQFP package_pins: 64 S1JA series: 1 S1JA Family OFS0 register settings: Select fields below IWDT Start Mode: IWDT is Disabled IWDT Timeout Period: 2048 cycles IWDT Dedicated Clock Frequency Divisor: 128 IWDT Window End Position: 0% (no window end position) IWDT Window Start Position: 100% (no window start position) IWDT Reset Interrupt Request Select: Reset is enabled IWDT Stop Control: Stop counting when in Sleep, Snooze mode, or Software Standby WDT Start Mode Select: Stop WDT after a reset (register-start mode) WDT Timeout Period: 16384 cycles WDT Clock Frequency Division Ratio: 128 WDT Window End Position: 0% (no window end position) WDT Window Start Position: 100% (no window start position) WDT Reset Interrupt Request: Reset WDT Stop Control: Stop counting when entering Sleep mode OFS1 register settings: Select fields below Voltage Detection 0 Circuit Start: Voltage monitor 0 reset is disabled after reset Voltage Detection 0 Level: 1.90 V HOCO OScillation Disable: HOCO oscillation is disabled after reset MPU - Enable or disable PC Region 0: Disabled MPU - PC0 Start: 0x000FFFFC MPU - PC0 End: 0x000FFFFF MPU - Enable or disable PC Region 1: Disabled MPU - PC1 Start: 0x000FFFFC MPU - PC1 End: 0x000FFFFF MPU - Enable or disable Memory Region 0: Disabled MPU - Memory Region 0 Start: 0x000FFFFC MPU - Memory Region 0 End: 0x000FFFFF MPU - Enable or disable Memory Region 1: Disabled MPU - Memory Region 1 Start: 0x200FFFFC MPU - Memory Region 1 End: 0x200FFFFF MPU - Enable or disable Memory Region 2: Disabled MPU - Memory Region 2 Start: 0x407FFFFC MPU - Memory Region 2 End: 0x400DFFFF MPU - Enable or disable Memory Region 3: Disabled MPU - Memory Region 3 Start: 0x400DFFFC MPU - Memory Region 3 End: 0x400DFFFF Synergy Common Main stack size (bytes): 0x1000 Process stack size (bytes): 0 Heap size (bytes) - A minimum of 4K (0x1000) is required if standard library functions are to be used.: 0x1000 MCU Vcc (mV): 3300 MCU Analog Power Supply AVCC0 (mV): 3300 Parameter checking: Enabled Assert Failures: Return SSP_ERR_ASSERTION Error Log: No Error Log ID Code Mode: Unlocked (Ignore ID) ID Code (32 Hex Characters): FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF Clocks XTAL 12000000Hz HOCO 48MHz Clock Src: HOCO ICLK Div /2 PCLKB Div /2 PCLKD Div /1 FCLK Div /2 Clock Src: HOCO SDADCCLK Div /12 Pin Configurations TB_S1JA.pincfg -> g_bsp_pin_cfg ADREG 37 SDADC0_ADREG - - - - - - - AVCC0 56 ANALOG0_AVCC0 - - - - - - - AVCC1 39 ANALOG0_AVCC1 - - - - - - - AVSS0 57 ANALOG0_AVSS0 - - - - - - - AVSS1 40 ANALOG0_AVSS1 - - - - - - - P000 63 - - - - Disabled - - "AGT1: AGTIO; CTSU0: TS16; GPT4: GTIOCB; ICU0: IRQ04; IIC0: SCL; KINT0: KRM0; SCI9: RXD; SCI9: SCL; SPI1: MISO" P001 62 CTSU0_TS15 - Low None "Peripheral mode" - None "CTSU0: TS15; ICU0: IRQ00; RTC0: RTCOUT; SCI9: CTS; SPI1: RSPCK" P002 61 - - - - Disabled - - "ADC0: AN07; DAC81: DA; OPAMP2: AMP+" P003 60 ADC0_AN06 - - - "Analog mode" - None "ADC0: AN06; OPAMP2: AMP-" P012 55 - - - - Disabled - - "ADC0: AN08; OPAMP2: AMPO" P013 54 - - - - Disabled - - "ACMPHS0: IVCMP; ACMPHS0: IVREF; ADC0: AN05; DAC80: DA; GPT6: GTIOCB; OPAMP1: AMP+" P014 53 - - - - Disabled - - "ACMPHS0: IVREF; ADC0: AN04; ANALOG0: VREFL; GPT6: GTIOCA; OPAMP1: AMP-" P015 52 - - - - Disabled - - "ADC0: AN03; OPAMP1: AMPO" P100 48 - - - - Disabled - - "ACMPHS0: IVCMP; ADC0: AN16; CTSU0: TS23; GPT5: GTIOCB; ICU0: IRQ04; SCI9: SDA; SCI9: TXD; SDADC0: ANSDP0" P101 47 - - - - Disabled - - "ACMPHS0: IVREF; ADC0: AN17; CTSU0: TS22; GPT5: GTIOCA; ICU0: IRQ05; SCI9: RXD; SCI9: SCL; SDADC0: ANSDN0" P102 46 - - - - Disabled - - "ADC0: AN18; CTSU0: TS21; GPT6: GTIOCB; SCI9: CTS; SDADC0: ANSDP1; SPI1: SSL0" P103 45 - - - - Disabled - - "ADC0: AN19; CTSU0: TS20; GPT6: GTIOCA; SDADC0: ANSDN1; SPI1: RSPCK" P104 44 - - - - Disabled - - "ADC0: AN20; CTSU0: TS19; ICU0: IRQ06; SDADC0: ANSDP2; SPI1: MISO" P105 43 - - - - Disabled - - "ADC0: AN21; CTSU0: TS18; ICU0: IRQ07; SDADC0: ANSDN2; SPI1: MOSI" P106 42 - - - - Disabled - - "ADC0: AN22; SDADC0: ANSDP3" P107 41 - - - - Disabled - - "ADC0: AN23; SDADC0: ANSDN3" P108 33 DEBUG0_SWDIO - Low - "Peripheral mode" - None "DEBUG0: SWDIO" P109 64 - - - - Disabled - - "ACMP(0-1): VCOUT; ACMPLP0: CMPREF; ADC0: ADTRG; AGT0: AGTOA; CTSU0: TS17; GPT_POEG1: GTETRG; GPT1: GTIOCB; ICU0: IRQ03; IIC1: SCL; KINT0: KRM1; SCI0: SCK; SCI9: SDA; SCI9: TXD; SPI0: MISO" P110 34 - - - - Disabled - - "ACMPLP1: CMPREF; ADC0: ADTRG; AGT0: AGTOB; CAN0: CTX; CGC0: CLKOUT; CTSU0: TSCAP; GPT_OPS0: GTOWLO; GPT2: GTIOCB; ICU0: IRQ02; IIC1: SDA; SCI0: SDA; SCI0: TXD; SCI9: RXD; SCI9: SCL; SPI0: RSPCK" P111 35 - - - - Disabled - - "CTSU0: TS14; ICU0: IRQ06; IIC1: SCL; RTC0: RTCOUT; SPI0: RSPCK" P112 36 GPIO nShutdown Low None "Output mode (Initial Low)" CMOS - "CGC0: CLKOUT; CTSU0: TSCAP; ICU0: IRQ07; IIC1: SDA; SPI0: SSL0" P200 27 - - - - Disabled - - "ICU0: NMI" P201 26 GPIO - - - "Input mode" - None "SYSTEM0: MD" P204 24 - - - - Disabled - - "CTSU0: TS09; SCI0: RXD; SCI0: SCL; SCI9: SCK; SPI1: MOSI" P205 23 GPIO - Low None "Output mode (Initial Low)" CMOS - "CTSU0: TS08; GPT_OPS0: GTOVLO; GPT3: GTIOCB; ICU0: IRQ00; IIC1: SDA; SCI0: SDA; SCI0: TXD; SCI1: CTS; SPI1: MISO" P206 22 GPIO - - IRQ06 "Input mode" - None "AGT0: AGTIO; CTSU0: TS07; GPT_OPS0: GTOVUP; GPT3: GTIOCA; ICU0: IRQ06; IIC1: SCL; SCI0: CTS; SCI1: SDA; SCI1: TXD; SPI1: SSL0" P212 10 - - - - Disabled - - "AGT0: AGTIO; CGC0: EXTAL; GPT_POEG1: GTETRG; GPT0: GTIOCB; ICU0: IRQ03; SCI1: SDA; SCI1: TXD" P213 9 - - - - Disabled - - "AGT1: AGTEE; CGC0: XTAL; GPT_POEG0: GTETRG; GPT0: GTIOCA; ICU0: IRQ02; SCI1: RXD; SCI1: SCL" P214 7 - - - - Disabled - - "CGC0: XCOUT" P215 6 - - - - Disabled - - "CGC0: XCIN" P300 32 DEBUG0_SWCLK - Low - "Peripheral mode" - None "DEBUG0: SWCLK" P301 31 SCI0_RXD - Low None "Peripheral mode" CMOS None "AGT1: AGTOB; CTSU0: TS13; GPT_OPS0: GTOWUP; GPT2: GTIOCA; ICU0: IRQ05; IIC0: SDA; KINT0: KRM4; RTC0: RTCOUT; SCI0: RXD; SCI0: SCL; SCI9: CTS; SPI1: MOSI" P302 30 SCI0_TXD - Low None "Peripheral mode" CMOS None "AGT1: AGTOA; CAC0: CACREF; CTSU0: TS12; GPT_OPS0: GTOVLO; GPT3: GTIOCB; ICU0: IRQ04; KINT0: KRM5; SCI0: SDA; SCI0: TXD; SCI1: RXD; SCI1: SCL; SPI1: RSPCK" P303 29 GPIO - Low - "Output mode (Initial High)" - - "CAN0: CRX; CTSU0: TS11; GPT6: GTIOCB; KINT0: KRM6; SCI0: CTS; SCI1: SCK; SPI0: MOSI" P304 28 GPIO - - - "Input mode" - None "CAN0: CTX; CTSU0: TS10; GPT6: GTIOCA; KINT0: KRM7; SCI0: SCK; SCI9: SDA; SCI9: TXD; SPI0: MISO" P400 1 - - - - Disabled - - "ACMPLP0: CMPIN; AGT0: AGTEE; CTSU0: TS00; GPT_POEG0: GTETRG; GPT1: GTIOCA; ICU0: IRQ00; IIC1: SDA; KINT0: KRM2; RTC0: RTCOUT; SCI0: CTS; SCI1: RXD; SCI1: SCL; SPI0: MOSI" P401 2 - - - - Disabled - - "ACMP(0-1): VCOUT; AGT1: AGTEE; CTSU0: TS01; GPT_OPS0: GTIU; GPT4: GTIOCA; ICU0: IRQ05; IIC0: SDA; KINT0: KRM3; SCI0: SCK; SCI9: SCK; SPI1: SSL1" P402 3 - - - - Disabled - - "CTSU0: TS02; GPT_OPS0: GTIV; GPT0: GTIOCA; SCI9: CTS; SPI1: SSL2" P403 4 - - - - Disabled - - "CTSU0: TS03; GPT_OPS0: GTIW; GPT0: GTIOCB; SCI1: SCK; SPI1: SSL3" P407 16 USBFS0_VBUS - Low None "Peripheral mode" CMOS None "AGT0: AGTIO; CAC0: CACREF; CAN0: CTX; CTSU0: TSCAP; GPT_OPS0: GTOULO; GPT0: GTIOCB; ICU0: IRQ01; IIC0: SCL; SCI0: SDA; SCI0: TXD; SCI9: SDA; SCI9: TXD; SPI1: RSPCK; USB_FS0: VBUS; USB_FS0: VBUS" P408 15 - - - - Disabled - - "ACMPLP1: CMPIN; AGT0: AGTO; CAN0: CRX; CTSU0: TS06; GPT_OPS0: GTOUUP; GPT0: GTIOCA; ICU0: IRQ01; IIC0: SDA; SCI0: RXD; SCI0: SCL; SCI1: SDA; SCI1: TXD; SPI0: SSL0" P409 14 CTSU0_TSCAP - Low None "Peripheral mode" CMOS None "AGT1: AGTO; CAN0: CTX; CTSU0: TSCAP; GPT0: GTIOCA; ICU0: IRQ07; IIC0: SCL; SCI0: SCK; SCI1: CTS; SPI0: SSL1" P410 13 - - - - Disabled - - "CTSU0: TS05; GPT5: GTIOCB; SCI0: CTS; SCI1: SDA; SCI1: TXD; SPI0: SSL2" P411 12 - - - - Disabled - - "CTSU0: TS04; GPT5: GTIOCA; SCI0: SDA; SCI0: TXD; SCI1: RXD; SCI1: SCL; SPI0: SSL3" P500 49 - - - - Disabled - - "ACMPHS0: IVCMP; ACMPHS0: IVREF; ADC0: AN00; CTSU0: TS24; DAC0: DA; GPT5: GTIOCA; ICU0: IRQ03; OPAMP0: AMP+; SCI0: RXD; SCI0: SCL" P501 50 - - - - Disabled - - "ACMPHS0: IVREF; ADC0: AN01; CTSU0: TS25; GPT5: GTIOCB; ICU0: IRQ02; OPAMP0: AMP-; SCI0: SDA; SCI0: TXD" P502 51 - - - - Disabled - - "ADC0: AN02; ICU0: IRQ01; OPAMP0: AMPO; SCI0: CTS" P914 19 USBFS0_DP - - - "Peripheral mode" - - "USB_FS0: DP" P915 18 USBFS0_DM - - - "Peripheral mode" - - "USB_FS0: DM" RES# 25 SYSTEM0_RES - - - - - - - SBIAS/VREFI 38 SDADC0_SBIAS - - - - - - - VCC 11 SYSTEM0_VCC - - - - - - - VCCUSB 20 USBFS0_VCC - - - - - - - VCCUSBLDO 21 USBFS0_VCCLDO - - - - - - - VCL 5 SYSTEM0_VCL - - - - - - - VREFH - ANALOG0_VREFH - - - - - - - VREFH0 59 ANALOG0_VREFH0 - - - - - - - VREFL0 58 ANALOG0_VREFL0 - - - - - - - VSS 8 SYSTEM0_VSS - - - - - - - VSSUSB 17 USBFS0_VSS - - - - - - - Module "CGC Driver on r_cgc" Parameter Checking: Default (BSP) Main Oscillator Wait Time: 2048 us (16384 cycles) Main Oscillator Clock Source: Crystal or Resonator Subclock Drive: Normal Mode Configure Subclock Drive On Reset: Enabled Low Voltage Mode: Disable Module "ELC Driver on r_elc" Parameter Checking: Default (BSP) Module "I/O Port Driver on r_ioport" Parameter Checking: Default (BSP) Module "FMI Driver on r_fmi" Parameter Checking: Default (BSP) SSP MCU Information Symbol Name: g_fmi_data Part Number Mask: 0xFE00 Module "UART Driver on r_sci_uart" External RTS Operation: Disable Reception: Enable Transmission: Enable Parameter Checking: Default (BSP) Module "Transfer Driver on r_dtc" Parameter Checking: Default (BSP) Software Start: Disabled Linker section to keep DTC vector table: .ssp_dtc_vector_table Module "Timer Driver on r_gpt" Parameter Checking: Default (BSP) Module "Flash Driver on r_flash_lp" Parameter Checking: Default (BSP) Code Flash Programming Enable: Disabled HAL Instance "g_elc ELC Driver on r_elc" Name [Fixed]: g_elc Instance "g_cgc CGC Driver on r_cgc" Name [Fixed]: g_cgc Instance "g_ioport I/O Port Driver on r_ioport" Name [Fixed]: g_ioport Instance "g_fmi FMI Driver on r_fmi" Name: g_fmi Instance "g_uart0 UART Driver on r_sci_uart" Name: g_uart0 Channel: 0 Baud Rate: 115200 Data Bits: 8bits Parity: None Stop Bits: 1bit CTS/RTS Selection: RTS (CTS is disabled) Name of UART callback function to be defined by user: user_uart_callback Name of UART callback function for the RTS external pin control to be defined by user: NULL Clock Source: Internal Clock Baudrate Clock Output from SCK pin: Disable Start bit detection: Falling Edge Noise Cancel: Disable Bit Rate Modulation Enable: Enable Receive FIFO Trigger Level: One Receive Interrupt Priority: Priority 2 Transmit Interrupt Priority: Priority 2 Transmit End Interrupt Priority: Priority 2 Error Interrupt Priority: Disabled Baudrate Percent Error: 2.0 UART Communication Mode: RS232 UART RS485 Communication Mode: Half Duplex RS485 DE Port: 09 RS485 DE Pin: 14 Instance "g_transfer0 Transfer Driver on r_dtc SCI0 TXI" Name: g_transfer0 Mode: Normal Transfer Size: 1 Byte Destination Address Mode: Fixed Source Address Mode: Incremented Repeat Area (Unused in Normal Mode): Source Interrupt Frequency: After all transfers have completed Destination Pointer: NULL Source Pointer: NULL Number of Transfers: 0 Number of Blocks (Valid only in Block Mode): 0 Activation Source (Must enable IRQ): SCI0 TXI Auto Enable: False Callback (Only valid with Software start): NULL ELC Software Event Interrupt Priority: Disabled Instance "g_transfer1 Transfer Driver on r_dtc SCI0 RXI" Name: g_transfer1 Mode: Normal Transfer Size: 1 Byte Destination Address Mode: Incremented Source Address Mode: Fixed Repeat Area (Unused in Normal Mode): Destination Interrupt Frequency: After all transfers have completed Destination Pointer: NULL Source Pointer: NULL Number of Transfers: 0 Number of Blocks (Valid only in Block Mode): 0 Activation Source (Must enable IRQ): SCI0 RXI Auto Enable: False Callback (Only valid with Software start): NULL ELC Software Event Interrupt Priority: Disabled Instance "g_timer0 Timer Driver on r_gpt" Name: g_timer0 Channel: 0 Mode: Periodic Duty Cycle Range (only applicable in PWM mode): Shortest: 2 PCLK, Longest: (Period - 1) PCLK Period Value: 1 Period Unit: Milliseconds Duty Cycle Value: 50 Duty Cycle Unit: Unit Raw Counts Auto Start: True GTIOCA Output Enabled: False GTIOCA Stop Level: Pin Level Low GTIOCB Output Enabled: False GTIOCB Stop Level: Pin Level Low Callback: timer_1ms Overflow Interrupt Priority: Priority 3 (lowest - not valid if using ThreadX) Instance "g_flash0 Flash Driver on r_flash_lp" Name: g_flash0 Data Flash Background Operation: Disabled Callback: NULL Flash Ready Interrupt Priority: Disabled Messaging